您好,欢迎来到维库电子市场网 登录 | 免费注册
1年
企业信息

深圳市骏旺微电子有限公司

卖家积分:1001分-2000分

营业执照:已审核

经营模式:原厂制造商

所在地区:广东 深圳

人气:11094
企业档案

相关证件:营业执照已审核 

会员类型:

会员年限:1年

王小姐 QQ:5027252761

电话:18123953487

手机:18123953487

王怡 QQ:1073653131

电话:18923864065

手机:18923864065

阿库IM:

地址:深圳市南山区沙河街道

E-mail:sz13798462711@126.com

供应aP8942A原装可编程OTP语音芯片IC
供应aP8942A原装可编程OTP语音芯片IC
<>

aP8942A原装可编程OTP语音芯片IC

型号/规格:

aP8942A

品牌/商标:

骏旺微

封装:

dip/sop

批号:

23+

定制:

客户要求定制语音程序

PDF资料:

点击下载PDF

产品信息

FEATURES
? Standard CMOS process.
? Embedded 1M bits EPROM.
? 42 sec Voice Length at 6KHz sampling and 4-bit ADPCM compression.
? Maximum 32 voice groups.
? Combination of voice blocks to extend playback duration.
? 960 table entries are available for voice block combinations.
? User selectable PCM or ADPCM data compression.
? Two triggering modes are available (EPROM programmable options).
- Key Trigger Mode – Combinations of S1 ~ S8 to trigger 32 Voice Groups; SBT
sequential trigger is possible.
- CPU Parallel Trigger Mode – Combinations of S1 ~ S5 with SBT goes HIGH to
strobe start the voice playback.
? Voice Group Trigger Options: Edge / Level; Hold / Un-hold; Retrigger / Non-retrigger.
? Whole Chip Options: Ramp / No-ramp; Output Options; Key / CPU trigger mode.
? 16ms (@ 8KHz sampling rate) Debounce Time for both Key and CPU Trigger Mode.
? RST pin set to HIGH to stop playback at once.
? Two user programmable outputs for STOP pulse, BUSY signal and flashing LED.
? Built-in oscillator to control sampling frequency with an external resistor.
? 2.6V – 5.0V; Wide range single power supply and < 5uA low stand-by current.
? PWM Vout1 and Vout2 drive speaker directly.
? D/A COUT to drive speaker through an external BJT.
? Development System support voice compilation and options selection.


 aP8942A


 产品特点:


 aP8942A标准CMOS工艺。

 

aP8942A内置1MEPROM

 

aP8942A6KHz采样和4bit ADPCM压缩下42秒的语音长度。

 

aP8942Azui32组声音

 

aP8942A声音切片组合,延长播放时间。

 

960段语音模块可重复组合。

 

●用户可选择PCMADPCM数据压缩。

 

●两个触发模式可用于选择(EPROM可编程选项)。

 

◆按键触发模式◆CPU并行触发模式

 

●语音组触发选项:边沿/电平;保持/取消保持;重新触发/非再触发。

 

●整个芯片选项:Ramp / No-ramp;输出选项;按键/ CPU触发模式。

 

RST引脚设置为HIHG停止播放yi次。

 

三种用户可编程的输出,停止脉冲,BUSY信号和闪烁的LED

 

用一个外部电阻来调整内部振荡器去控制采样频率

 

2.6V - 5.0V单电源供电和<5UA低待机电流。

 

 

PWM VOUT1VOUT2直接驱动扬声器。

 

D/A COUT通过外部BJT驱动扬声器。

 

●桌面系统支持语音编辑和开发选项的选择。