您好,欢迎来到维库电子市场网 登录 | 免费注册
1年
企业信息

深圳市骏旺微电子有限公司

卖家积分:1001分-2000分

营业执照:已审核

经营模式:原厂制造商

所在地区:广东 深圳

人气:28103
企业档案

相关证件:营业执照已审核 

会员类型:

会员年限:1年

王小姐 QQ:5027252761

电话:18123953487

手机:18123953487

王怡 QQ:1073653131

电话:26983158

手机:26983158

阿库IM:

地址:深圳市南山区沙河街道

E-mail:sz13798462711@126.com

供应aP89170原装可编程OTP语音芯片IC
供应aP89170原装可编程OTP语音芯片IC
<>

aP89170原装可编程OTP语音芯片IC

型号/规格:

aP89170

品牌/商标:

APLUS

封装:

DIP24/SOP28

批号:

23+

定制:

客户要求定制语音程序

PDF资料:

点击下载PDF

产品信息

aP89170  语音ic

产品特点:


aP89170标准CMOS工艺。


aP89170内置4M EPROM


aP89170 6KHz采样和4bit ADPCM压缩下170秒的语音长度


 254组声音。


 声音切片组合,延长播放时间


7680段语音模块可重复组合


用户可选择PCMADPCM数据压缩


●三种触发模式可供选择(通过M1M0输入引脚控制)


◆按键触发模式◆CPU并行模式◆CPU串行模式


●语音组触发选项:边沿/电平;保持/取消保持;重新触发/非再触发。


●整个芯片选项:Ramp / No-ramp;;输出选项;/短反跳时间。


●可选16毫秒或65us@ 8KHz的采样率)可选择去抖时间。


RST引脚设置为HIGH停止播放。


●三种用户可编程的输出,停止脉冲,BUSY信号和闪烁的LED


用一个外部电阻来调整内部振荡器去控制采样频率


2.2V - 3.6V单电源供电和<5UA低待机电流。


PWM VOUT1VOUT2直接驱动扬声器。


D / A COUT引脚通过一个外部驱动BJT扬声器。


●开发系统支持语音编辑。



FEATURES
Standard CMOS process.
Embedded 8M/4M/2M EPROM.
341/170/85 sec Voice Length at 6KHz sampling and 4-bit ADPCM compression.
Maximum 254 voice groups.
Combination of voice blocks to extend playback duration.
 7680 table entries are available for voice block combinations.
User selectable PCM or ADPCM data compression
Three triggering modes are available (controlled by M1 and M0 input pins):
   - Key Trigger Mode (M1=0, M0=0) - S1 ~ S8 to trigger up to 32 voice groups; SBT
   to trigger up to 254 voice groups sequentially.
   - CPU Parallel Trigger Mode (M1=0, M0=1) – S[8:1] services as 8-bits address to
  trigger up to 254 voice groups with SBT goes HIGH to strobe the address bits.
  - CPU Serial Command Mode (M1=1, M0=0) – user commands are clocked serially
   into the chip which enable user to fully control the operation of the chip.
Voice Group Trigger Options: Edge / Level; Hold / Un-hold; Retrigger / Non-retrigger.
Whole Chip Options: Ramp / No-ramp; Output Options; Long / Short debounce time.
Optional 16ms or 65us (@ 8KHz sampling rate) selectable debounce time
RST pin set to HIGH to stop the playback at once
Three user programmable outputs for STOP pulse, BUSY signal and flashing LED.
Built-in oscillator to control sampling frequency with an external resistor
2.2V – 3.6V single power supply and < 5uA low stand-by current
PWM Vout1 and Vout2 drive speaker directly
D/A COUT pin drives speaker through an external BJT
Development System support voice compilation.